MLFH330 無限コーティングプレミアム 高能率レンズ形3枚刃エンドミル

6 パターン① 壁のない形状の場合 Pattern 1: No wall shape パターン② ポケット形状の場合 Pattern 2: Pocket shape ボールエンドミルとして定義 Define the tool shape as “Ball end mill” ラジアスエンドミルとして定義 Define the tool shape as “Corner radius end mill” 適用形状 Applicable shape MLFH330定義イメージ MLFH330 definition image 適用形状 Applicable shape MLFH330定義イメージ MLFH330 definition image CAMの設定方法 Way to set up CAM CAMの設定方法 Way to set up CAM 小径でありながらピックフィードを大きくとることが可能 ボールエンドミルよりも生産性を向上させるレンズ形3枚刃エンドミル Realizes large pick feed even with small size diameter Specialized lens form 3-Flute end mill improves productivity compared to ball end mills 形状 刃先形状 工具外径(D) 刃長 テーパ角度 刃数 コーナ半径(R) ラジアス 6 0.789 3 0 6 ①工具形状は「ラジアスエンドミル」として定義してください Define the tool shape as “Corner radius end mill” ②MLFH330の近似Rをコーナ半径として入力してください Enter the theoretical corner radius of MLFH330 as the tool corner radius 形状 刃先形状 工具外径(D) 刃長 テーパ角度 刃数 ボール半径(R) ボール 16 8 3 0 6 ①刃先形状は「ボールエンドミル」として定義してください Define the tool shape as “ball end mill” ②MLFH330の底刃半径(R)の2倍を工具外径として入力してください Enter twice the end tooth bottom radius (R) of MLFH330 as the tool diameter 使用工具:MLFH330 φ6×R8×20の場合 Tool 使用工具:MLFH330 φ6×R8×20の場合 Tool ●工具の設定について Tool setting ■ MLFH330使用時のポイント Points of using MLFH330 お使いのCAMがMLFH330の工具形状を登録できる 弊社ホームページでSTEP・DXFファイルを配布中 干渉チェック・ツールパス作成時にお役立てください ぜひ一度、MLFH330をお試しください! MLFH330の工具形状を登録できないCAMでも パラメータの簡単な工夫で使用可能! 下の工具の設定についてをご覧ください CAM software can define the tool shape of MLFH330(Lens shape) STEP and DXF files are distributed on our website. Please use them to check interference and create tool paths. Please give it a try! If CAM software cannot define the tool shape of MLFH330, please use it with a simple adjustment of the parameters! Please see the tool settings below はい いいえ ワークの4方向が開けた形状 No wall shape 壁がある(ポケット)形状 Pocket shape 詳細は弊社ホームページのMLFH330紹介ページをご覧ください For details, please see the MLFH330 introduction page on our website 日本語 English ※近似Rは8ページの規格表をご覧ください For approximate R, please refer the specifications table on page 8

RkJQdWJsaXNoZXIy NDY3NTA=